top of page

Meet the Makers: Why Great Custom Glass Begins Long Before Installation

7 days ago
7 min read

Updated: 6 days ago

When we think about glass in residential interiors, the first thing people usually picture is a shower enclosure. And while showers are a significant part of what DT Glass creates, my conversation with owner Shannon McKinney made one thing very clear: custom glass has far more design potential, and requires far more planning, than most people realize.


I first discovered Shannon through an NKBA webinar, where she was teaching designers about the practical and creative applications of architectural glass. Her willingness to explain not only what can be done, but what must happen behind the scenes to do it well, immediately caught my attention.


So I reached out, and she invited me to Oregon City, Oregon, to visit DT Glass, the company she owns with her husband, Mike. I wanted to see and understand how I, as a designer, can better specify my projects, and all the steps required to move custom glass from an idea on a set of plans to a precisely fabricated and installed architectural element.


Shannon highlighted so well how glass may be one of the final materials installed in a home, but it should never be one of the final materials considered.


Exterior of the DT Glass showroom, featuring a red brick facade, glass entry doors, and signage highlighting the company's glass design, fabrication, and installation services.

A Rare Level of Control


DT Glass has been in business since 1997. When Shannon and Mike purchased the company in 2010, they began focusing more intentionally on custom residential glass. In 2017, in the interest of maintaining better quality control, they added their own fabrication facility.


This unique distinction matters.


The majority of glass companies measure and install glass that has been fabricated elsewhere. DT Glass handles the process from design and measurement through fabrication and installation. Large sheets of glass arrive at their Oregon City facility, where they are cut, edged, drilled, notched, tempered, coated, inspected, and prepared for installation.


Managing the process in-house gives the team greater control over quality, fit, lead times, and problem-solving. More importantly, the people fabricating the glass understand how it will ultimately be supported, installed, and used.


Custom glass is not simply ordered by width and height. Walls are rarely perfectly plumb. Floors and curbs may not be level. Corners are not always square. Tile can introduce unexpected projections and irregularities. Each piece must be fabricated for the exact conditions of the project, and once glass has been tempered, it cannot be cut or altered.


There is very little room for improvisation at the end.


Lisa of Simop Designs speaks with the owner of DT Glass inside the showroom, surrounded by custom glass shower enclosures, hardware displays, and architectural glass samples.

My Favorite Part: Where Precision Becomes Permanent


My favorite part of the tour, hands down, was watching the tempering process.


After the glass has been cut, edged, drilled, and notched, it enters a massive tempering furnace that Shannon jokingly described as her husband's Ferrari. We watched an eight-by-six-foot sheet of glass heat until it glowed red-orange through and through.


The glass then emerged from the furnace and continued rolling back and forth as it cooled. That constant movement is essential. It allows the glass to cool evenly so it does not distort or “pool” in certain areas.


This is also the point of no return. Once glass has been tempered, it cannot be cut, drilled, or altered. Every measurement, opening, notch, and hardware location must already be correct.


It is one thing to understand that custom glass requires precision. It is another to stand in front of a furnace and watch exactly why that precision matters.


Display of custom glass shower door hardware, including chrome, black, and brass handles and hinges, alongside textured and decorative glass samples at the DT Glass showroom.

Glass Is More Than a Shower Enclosure


Showers may be the most familiar application, but they are only the beginning.


DT Glass also creates glass wine rooms, wet-room enclosures, sauna doors, interior partitions, home offices, exercise-room enclosures, shelving, cabinet glass, back-painted glass, and custom mirrors, including antique and specialty mirror installations. The possibilities are really only limited to the imagination of the person designing for it.


Glass can divide a room without sacrificing natural light. It can create acoustic separation for an office while preserving a visual connection to the surrounding home. It can turn a wine collection into an architectural feature or provide a clean, durable surface through back-painted glass- including in a kitchen. (seamless splash anyone?)


This is where involving a knowledgeable fabricator becomes especially valuable. A designer may begin with the aesthetic intention, but the fabricator understands the panel sizes, glass thicknesses, hardware, support, access, and installation sequence required to make that intention buildable.


The best results come from bringing those perspectives together before construction begins.



The Glass Brief: Straight Answers from Shannon


After seeing how the glass is fabricated, I asked Shannon to address questions designers and homeowners should consider long before installation day.


When should the glass fabricator become involved?


Earlier than most people think.


Glass may be installed near the end of a project, but decisions about panel size, door placement, hardware, blocking, plumbing, curbs, benches, and finished tile affect what will ultimately be possible.


Shannon also frequently sees plans that do not show the glass at all. That leaves the installer to determine what belongs in the remaining opening, often after the most important decisions can no longer be changed.


The fabricator should be involved while those details can still be resolved on paper, not after the tile is complete.


What do you look for when reviewing plans?


Panel size and structural support are among the first things I consider.


A large panel may not have sufficient support, particularly as showers expand across entire walls and we continue to favor minimal hardware. At the other extreme, a narrow piece of glass may be too small to temper without warping.


Shannon also looks at how the glass will meet the surrounding construction. An overhanging countertop, projecting tile, bench, niche, or pony wall can interfere with a door or require an entirely different configuration.


A good design still depends on the supporting construction being built plumb, level, and square.


Is frameless glass watertight?


No- but if it's not talked about, people get upset when they have it installed then find out it is not. As Shannon put it directly, “Frameless glass leaks.”


That does not mean the enclosure is defective. Frameless glass has intentional gaps around doors, hinges, and adjoining panels. It was never intended to manage water by itself.


The shower must function as a complete water-management system. Curbs, benches, and pony walls should slope inward. The drain should pull water away from the entrance. Shower heads and body sprays should direct water away from door gaps.


Shannon generally prefers placing the shower head on the same side as the door hinges so the spray travels past the hinge gap rather than directly into it.


In her words, shower glass “is not an aquarium.”


Lisa of Simop Designs speaks with the owner of DT Glass in the showroom while exploring decorative glass samples, mirrored finishes, and custom glass options for interior design projects.

What makes a curbless shower successful?


More planning, not less.


Removing the curb also removes one of the elements that helps contain water. The shower floor must direct water toward the drain, while the bathroom floor outside the shower must remain level enough for the door to swing outward.


If the exterior floor slopes away from the shower, escaped water is encouraged farther into the room. If it slopes toward the shower, the door may strike the floor as it opens.


Curbless showers offer a beautiful transition and support accessible and aging-in-place design, but their simplicity is deceptive. The cleaner the detail appears, the more precise the construction must be.


Are open, doorless showers practical?


They can be, provided the homeowner understands the trade-offs.


A single fixed panel creates the minimal look seen throughout magazines and Pinterest. In daily use, however, the shower may feel colder and allow more water to escape than anticipated.


Shannon recommends designing the enclosure so a door can be added later. This allows the homeowner to try the open concept without risking a complete teardown if it does not function as expected.


Good design is not only about achieving a beautiful photograph, though we certainly want that too. It is about anticipating how the room will feel and function every day.


Which upgrades are actually worth the money?


Thicker glass is not automatically better.


Both ⅜-inch and ½-inch glass can be used in frameless shower construction. Half-inch glass is heavier, more expensive, and may require heavy-duty hardware. DT Glass generally recommends it when the added thickness serves a structural purpose, such as supporting a door from a fixed panel or stabilizing glass taller than approximately 96 inches.


Low-iron glass can be a more visible upgrade in the right setting. Standard glass contains iron, which creates a green cast, especially along exposed edges. Low-iron glass appears clearer and can make a noticeable difference beside white tile, pale stone, or subtle material colors.


In a darker shower or one surrounded by green or strongly colored finishes, the added cost may not be justified.

This is a good example of why luxury does not mean automatically choosing the most expensive option. It means knowing where the difference will actually be seen and appreciated.


What is the best way to keep shower glass looking new?


Begin with a reputable protective coating.


Although glass appears smooth, its surface contains microscopic peaks and valleys. Hard-water minerals, soap residue, and other deposits settle into those irregularities, eventually making untreated glass appear cloudy or etched.


A protective coating covers those areas, helps water shed from the surface, and makes remaining deposits easier to remove.


It does not make the shower maintenance-free, but it helps protect the clarity of one of the room’s most visible features. When the glass is intended to look almost invisible, keeping it clean is not a minor detail.


Lisa of Simop Designs and the owner of DT Glass examine a custom glass shower enclosure featuring clear glass panels, sleek hardware, and decorative tile inside the DT Glass showroom.

The Real Value of a Glass Specialist


The greatest value any glass specialist brings to a project is not simply the ability to produce a piece of glass in the correct dimensions. It is the accumulated knowledge to recognize what will not work, explain why, and offer a better solution before the mistake becomes permanent.


They understand how panel size affects support, how glass thickness affects hardware, how water moves through an enclosure, how the structure must be prepared, and how a design decision on paper will behave in daily life.

Shannon’s final advice was simple: plan ahead, visit showrooms, talk with local fabricators and installers, and ask about their process.


Designers and homeowners do not, and should not, need to become glass experts. But involving one early is where the experience and expertise matter.


Because the best custom glass does more than fit the opening. It supports the architecture, protects the function of the space, and makes a complex process look beautifully simple.


Shout out to Shannon for taking her time to give me a tour and teach me all about what she is doing over at DT Glass!


If you enjoyed this conversation, catch up on our previous features: a conversation about cabinetry trends and tips on choosing stone for your countertops from a stone fabricator.


red heart

Lisa

Let's Make Something Beautiful

 
 
bottom of page